Mechanical Music Digest 
You Are Not Logged In Login/Get New Account
Please Log In. Accounts are free!
Logged In users are granted additional features including a more current version of the Archives and a simplified process for submitting articles.
Home Archives Calendar Gallery Store Links Info
MMD > Pictures > knot

Tying a Knot in a Piano String
Tying a Knot in a Piano String
by Art Reblitz, John A. Tuttle, Jon Page (000118 MMDigest)

knot1.jpg (17 kb)


My book, "Piano Servicing, Tuning and Rebuilding", includes a four-step
procedure for tying a knot in a string, as illustrated by Douglas Strong
in the "Piano Technicians Journal" issue of November 1972 (and used with
permission).  It is shown on p. 106 of the second edition of my book.

When I pull up the pitch of a piano, I start in the middle and work
toward the treble, then finish in the bass.  If the strings are in
such bad condition that they will break when pulled up to pitch, this
condition usually manifests itself in the midrange.  My rule is that if
more than two midrange strings break during a pitch raising, I replace
them and make no further attempt to raise the pitch of that piano until
it is restrung.

Tuning thousands of pianos in the 1970s, I rarely had the occasion to
tie a bass string, because the fragile, rusty treble strings almost
always warned me not to proceed.  However, on one occasion, a perfectly
good looking bass string broke in a little early 1960s Cable grand made
by Aeolian-American.  As the strings still sounded and looked almost
like new, I thought I'd try the knot-tying technique.  The result of
my first attempt is illustrated on page 111.  As the photograph in the
book shows, this was in an area with very little working room.

After forming a coil in the new leader, placing it on the tuning pin,
and pulling the string up to pitch, the knot pulled tight -- just in the
right place -- and the string sounded just like its neighbors.  I later
decided that since I was able to do it on the first try, it was a tech-
nique worthy of inclusion in the book.  As I note in my text, "this
repair can be very challenging due to the stiffness of the wire; but
with strength, persistence, and great care taken not to cut your
fingers, it can be done."

Of course, if the string breaks in the sounding portion (between the
agraffe and the winding) it's difficult to tie a knot that doesn't
end up touching the agraffe as it tightens.

Art Reblitz
Sat, 15 Jan 2000 22:35:46 -0700


[ Jon Page wrote: ]

> The broken wire is in the piano, the splice is the add-on.
> When splicing onto an existing wire, there is only one free end.
> That is on the splice.  So the splice has to slip over the wire.
> If it slipped into the wire loop, how would you get the splice loop
> around the wire length?  See?
>
> First make a loop on the wire.  Make the loop on the splice and
> little larger so the wire loop will pass through.  Making a slight
> bend in the strings at the cross-over helps to align them.  The
> loops need to be opposed.
>
> So the splice loop passes over the wire loop and the splice's tail
> end is then inserted back into the wire loop and drawn together.
>
> Slide the splice over the wire and insert the tail-end of the
> splice into the wire loop.  Draw them together.
>
> Doing is easy, explaining takes a little more effort.

Hi Jon,  Attached is the scanned image of my first attempt at knotting,
using the heaviest gauge piano wire I have, an old worn-out pair of
needle nose pliers and your instructions.  It took me about seven
minutes, and I did it while sitting here at the computer.

I held the two pieces of wire in my hands, using no vice or other
gripping tools.  I did use a heavy set of pliers and a large vise
to pull the knot tight, but that would (I imagine) normally be
accomplished when the string is brought up to pitch.

Actually, your picture told the whole story.  The 'trick' is making
the loop in the existing string big enough to allow the loop in the
replacement piece of wire to pass though it and the up-bends so the
two loops align better.

The last time I tried to knot heavy wire, I spent about 30 minutes
bending and twisting the wire before I gave up in disgust and replaced
the broken bass string with a universal replacement string.

Thanks for the technique,

John A. Tuttle
Sat, 15 Jan 2000 13:33:59 -0500

knot2.jpg (22 kb)


20 January 2000

Home    Archives    Calendar    Gallery    Store    Links    Info   


Enter text below to search the MMD Website with Google



CONTACT FORM: Click HERE to write to the editor, or to post a message about Mechanical Musical Instruments to the MMD

Unless otherwise noted, all opinions are those of the individual authors and may not represent those of the editors. Compilation copyright 1995-2024 by Jody Kravitz.

Please read our Republication Policy before copying information from or creating links to this web site.

Click HERE to contact the webmaster regarding problems with the website.

Please support publication of the MMD by donating online

Please Support Publication of the MMD with your Generous Donation

Pay via PayPal

No PayPal account required

                                     
Translate This Page